|
 |
Photo Gallery |
|
| |
|
| |
|
| |
Acid proof
Chemical Proof
chemical resistance
Acid Resistant
Corrosion Proof
corrosive chemicals
corrosive India
acid proof lining flooring
acid proof bricks
Acid proof materials manufacturer
Chemical proof India
Acid Proof India
acid proof chemical manufacturer
Exporters of acid proof chemical
Acid Proof Material
industrial chimney
cement resin
Acid proof materials manufacturer
Indian Acid Proof Company
Acid Proof Manufacturer
Acid Proof India
Chemical Proof India |
| |
|
Search Us For: |
|
| |
Chemical resistant Materials,
acid resistant materials
acid proof materials
chemical proof materials
corrosion proof materials
corrosion solutions
corrosion treatment
epoxy lining
acid resistant lining
anti-corrosive treatment
anti-corrosive materials
red mandana stone flooring
acid resistant mastic lining
frp/frv lining
A.R. bricks lining
self leveling |
| |
|
|
|
| |
Modern Polymer Industries Manufucatuer and Exporter of |
| |
|
| |
| |
Chemical Resistant Bitumor™ Primer |
|
|
| Bitumor
Primer is Bituminous air curing ready mixed Acid & Alkali
resistant special primer. |
| |
| Application |
- Concrete
surface must be clean & dry and rough. No primer
should be applied over smooth and wet surface.
- After
cleaning the concrete surface, one coat of Bitumor
Primer should be applied with brush and allow to dry
thoroughly.
- The
drying time will depend upon the temperature.
|
| Packing |
| Bitumor
Primer |
25 Litre Drum |
|
| Note |
Bitumor
Primer contains Volatilt and slightly toxic solvent. keep
away from spark and open flames at working area. |
|
|
| |
| |
Chemical Resistant Bitumor™ Mastic |
|
|
Bitumor
Mastic is Acid and Alkali resistant for use as a protective
impervious membrane suitable for concrete, brick work, steel
etc. Bitumor Mastic have good resistance to large number
of mildly corrosive conditions.
| How
to Use |
Bitumor
Mastic shall be broken into small pieces and heated.
The surface on which it is to be applied should be
primed with Bitumor Primer. It is applied with straight
edged piece of wood or trowel. The surface shall not
be put under service before 24 hrs. of application
Mastic.
Bitumor Mastic is not recommended where there is excessive
heat or solvents, mineral oil & greases are anticipated.
It is adhesion to concrete surface previously primed
with Bitumor Primer. |
| Packing |
20
Kg. cake (approx) |
|
|
| |
| |
Furomor™ Corrosion Proof Furan Resin Mortar |
|
|
Furmor
is a Furan Resin based Chemical Resistant Mortar. When
the liquid Resin & Powder is mixed in proportion,
form workable mortar and after it setting and curing
gives a black solid mass.
| Furomor
Mortar Resistant to |
Acids,
Alkalies, Saltsm Solvent, Greases, Detergents, Oils. |
| Maximum
Temperature |
175°C |
| Application |
It
is widely used for Acid Resistant Bricks/Tiles
linging as a bedding and jointing mortar for Chemical
Reaction Vessels, Tanks, Floor, Drain, Foundation,
Neutralization Pit etc. It is also used for repairing
Glasslined Vessels.
Carbon Filled Furomor Mortar is to be used to
resist hot & highly concentrated Alkalies
, Hydrofloric Acid, Flourid Salts etc. |
| Packing |
| Furomor
Resin |
25
Kg. Drum |
| Furomor
Powder |
25
Kg. Bag |
|
|
|
|
|
| |
| |
Phenomor™ Corrosion Proof Phenolic Resin Mortar |
|
|
Phenomor
is a phenolic Resin based Chemical Resistant Mortar. When the liquid Resin & Powder is mixed in proporation,
forms workable mortar and after it setting and curing
gives a black solid mass.
| Phenomor
Mortar Resistant to |
Concentrated
H2SO4 acid, Phospheric acid
Non-oxidizing acids, Dilute Oxidizing acids, Solvents
and Neutral Salts. |
| Maximum
Temperature |
175°C |
| Application |
It
is widely used for Acid Resistant Bricks/ Tiles
lining as a bedding and jointing mortar for Chemical
Reaction Vessels, Tanks, floor, Drain, Foundation
etc. |
| Packing |
| Phenomor
Resin |
25
Kg. Drum |
| Phenomor
Powder |
25
Kg. Bag |
|
|
 |
|
|
| |
| |
Silimor™ Corrosion Proof silicate Solution Mortar |
|
|
Silimor
is a Silicate solution based Chemical Resistant Mortar.
When the liquid Resin & Powder is mixed in proportion
forms workable mortar and after it setting and curing
gives a Off-white solid mass.
| Silimor
Mortor resistant to |
Oxidizing
& Non-Oxidizing acids except Hydroflouric aicd. |
| Maximum
Temperature |
900°
C |
| Application |
It
is widely used for Acid Resistant Bricks/ Titles
lining as a bedding and jointing mortar for tanks
Floor, Drain, Foundation etc. |
| Packing |
| Silimor
Solution |
25
Kg. Drum |
| Silimor
Powder |
50
Kg. Bag. |
|
Prepatation
of Chemical Resistant Mortars consists of Resin &
Powder. The average mixing ratio necessary to obtain
mortar with good working consistency is 1 pbw Resin
& 3 pbw Powder. The ration will vary slightly depending
upon temperature and working condition.
Stirer
the Resin thoroughly before using. Place liquid resin
in a suitable mixing pan and add powder. Mix throughly
with the Spatula or Trowel. the mixing operation shall
be continued until a uniform mixture is obtained.
Make
sure that all the mortar is used from the mixing pan
before another batch is prepared. |
|
|
| |
| |
Sulphomor™ Corrosion Proof Mortar |
|
|
Sulphomor
is a Sulphur based mortar containing Plasticizer &
filter. The melt mortar is extremely fluid and pours
quite easily.
| Silimor
Mortor resistant to |
Non-Oxidizing
acids, dilute oxidizing acids and neutral salts. |
| Maximum
Temperature |
90°C |
| How
to Use |
The
mortar should be heated at low temperature in
a suitable Kettle by stirring with metal rod or
ladle. The surface shall be laid first with membrane.
Over the dry coat of membrane, the chemical resistant
bricks or tiles be placed on spacer chips. Melted
Sulphomor Mortar shall be poured through joints
of bricks or tiles. In case of vertical surface
joints of bricks or tiles are covered by applying
with adhesive paper. sulphomor mortar is poured
between the wall surface and the tile or bricks. |
| Note |
If
Sulphomor is over heated or ignited a tight cover
or wet gunny bags shall be kept ready for use in
case of fire. Sulphomor Mortar burns with a low
blue flame. If this should happen, heating should
be stopped and the vessel should be covered with
lid or wet gunny bags. if the mortar thickens or
over heating, it should be allowed to cool and stir
till it become thin. Care should be taken that water
or damp mortar should not fall in the heating vessel
in order to avoid foaming. |
| Packing |
| Sulphomor |
Ingot - 50 Kg. Bag |
| Power - 50 Kg Bag |
|
|
|
|
| |
| |
Cashewmor™ Corrorsion Proof C.N.S.L.Resin Mortar |
|
|
Cashewmor
is a C.N.S.L. Resin based Chemical Resistant Mortar. When the liquid Resin & Powder is mixted in
proportain, forms workable mortar and after it setting
and curing gives a black solid mass. It is relatively
Plastic in nature.
| Cashewmor
Mortor resistant to |
Acids,
Alkalies, mixed alkaline solutions with acids. |
| Maximum
Temperature |
180°
C |
| Application |
It
is widely used for Acid Resistant Bricks/ Tiles
lining as a bedding and jointing mortar. It can
be used for jointing Chemical Resistant Stoneware
Pipes. It is also used for ETP Plants. It is suitable
where excellent resistant property and heavy impacts
subjected to the surface of floors and tank is
required. Cashewmor mortar adheres strongly on
the Ceramic, Concrete surface and metals so, it
can be used as a monolithic lining for the construction
of dilute acids storage tanks. |
| Packing |
| Cashewmor
Resin |
25
Kg. Drum |
| Cashewmor
Powder |
25
Kg. Bag. |
|
|
 |
|
|
| |
| |
|
|
